Section


Brand


Availability


Panel Beater Pick & Finishing - Flat Face

Automotive > Bodywork Tools > Bodywork Tools
053000V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

 Flat Faced Hammers

Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

• Medium-weight flat face panel beater with round point pick head designed to remove low spots when finishing

- Round Face: 38mm

- Square Face: N/A

- Head Width: 135mm

- Weight: 0.43kg




Panel Beater Curved Pein - Crowned Face

Automotive > Bodywork Tools > Bodywork Tools
053700V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does

• Medium-weight, crowned face finishing panel beater with curved pein for use where access is restricted

- Round Face: 41mm

- Square Face: N/A

- Head Width: 142mm

- Weight: 0.425kg

 




thin curved dolly

Automotive > Bodywork Tools > Bodywork Tools
054301V2
Brand::Sykes Pickavant

• Lightweight curved dolly suitable for a wide variety of panel beating tasks - reforming beads and mouldings, reshaping panels, raising low spots

- Length: 125mm

- Width: 55mm

- Depth: 37mm

- Weight: 0.90kg




thin toe dolly

Automotive > Bodywork Tools > Bodywork Tools
054801V2
Brand::Sykes Pickavant

• Lightweight thin toe dolly enables access in difficult to reach areas

• 1 x flat face and 1 x curved face

- Length: 115mm

- Width: 56mm

- Depth: 25mm

- Weight: 0.86kg




anvil dolly

Automotive > Bodywork Tools > Bodywork Tools
054901V2
Brand::Sykes Pickavant

Anvil Dolly 054901V2

• General purpose dolly with two curved faces

- Length: 102mm

- Width: 72mm

- Depth: 62mm

- Weight: 1.40kg




utility dolly

Automotive > Bodywork Tools > Bodywork Tools
055201V2
Brand::Sykes Pickavant

• Double-ended general purpose dolly with two curved faces

- Length: 76mm
- Width: 57mm
- Depth: 58mm
- Weight: 1.15kg




heel dolly

Automotive > Bodywork Tools > Bodywork Tools
05540100
Brand::Sykes Pickavant

• Semi-circular model, ideal for rounded and contoured panels

• 1 x flat face and 1 x convex face

- Length: 83mm

- Width: 63mm

- Depth: 36mm

- Weight: 1.08kg




Adjustable Body Blade Holder c/w File Blade

Automotive > Bodywork Tools > Bodywork Tools
05710000
Brand::Sykes Pickavant

  • Adjustable blade holder, suitable for forming & shaping fillers and metal during body repair work
  • Steel tension adjuster and base plate
  • Supplied with a standard flat cut 9tpi blade
  • Compatible with most flat profile 356mm body blades
  • Robust construction with steel tension adjuster, sole plate and tough plastic handle
  • 2 position handle for vertical or horizontal use
  • Other blades also available - ask for details



Adjustable Body Blade Holder only

Automotive > Bodywork Tools > Bodywork Tools
05710100
Brand::Sykes Pickavant

  • Adjustable blade holder, suitable for forming & shaping fillers and metal during body repair work
  • Steel tension adjuster and base plate
  • Compatible with most flat profile 356mm body blades
  • Robust construction with steel tension adjuster, sole plate and tough plastic handle
  • 2 position handle for vertical or horizontal use
  • Individual blades available - ask for details



Body Blade Standard Flat Cut 9 tpi

Automotive > Bodywork Tools > Bodywork Tools
05711100
Brand::Sykes Pickavant

  • Specially heat treated alloy steel provides hardness with flexibility
  • Length: 356mm
  • Precision cut teeth
  • Blade edges chamfered
  • Maximum deflection of 14mm

 

 




Body Blade Fine Flat Cut 12 tpi

Automotive > Bodywork Tools > Bodywork Tools
05711200
Brand::Sykes Pickavant

  • Specially heat treated alloy steel provides hardness with flexibility
  • Length: 356mm
  • Precision cut teeth
  • Blade edges chamfered
  • Maximum deflection of 14mm

 




Body Blade Plasticut Flat Cut 6 tpi

Automotive > Bodywork Tools > Bodywork Tools
05711500
Brand::Sykes Pickavant

  • Specially heat treated alloy steel provides hardness with flexibility
  • Length: 356mm
  • Precision cut teeth
  • Blade edges chamfered
  • Maximum deflection of 14mm



general purpose spoon

Automotive > Bodywork Tools > Bodywork Tools
05740000
Brand::Sykes Pickavant

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

General Purpose Spoon 05740000

• Multi-purpose double ended spoon which is designed for panel beating where access is restricted and separating the outer panels from the inner frame structure

- Length: 295mm

- Width: 40mm

- Weight: 1.10kg




angled surface spoon

Automotive > Bodywork Tools > Bodywork Tools
05780000
Brand::Sykes Pickavant

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

Angled Surfacing Spoon 05780000

• Multi-purpose surfacing spoon,with specially designed angled head for panel beating work in restricted areas.

For example separating outer panels from inner frame structure depending on the amount of access available

- Length: 185mm

- Width: 45mm

- Weight: 1.56kg




bumping tool - flat

Automotive > Bodywork Tools > Bodywork Tools
05940000
Brand::Sykes Pickavant

• Flat steel blade with serrated teeth and pvc handle

• Suitable for removing bumps,dents & flattening wavy surfaces

• Ideal for semi-finishing work on body panels

• Milled serrations help prevent metal stretch

• 350 x 35mm




1303-CURVED DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1303
BETA

Curved dolly


1479 RB/3-FLAT PUTTY KNIFE SCRAPER

Automotive > Bodywork Tools > Bodywork Tools
1479RB/3
BETA

Flat putty knife scraper


4-piece set of plastic multi-use tools

Automotive > Bodywork Tools > Bodywork Tools
CR.D4
Facom

- For removing adhesive weights from wheels in alloy, silicon, elastic sealing products, hub caps, etc.
- No damage to plastic or varnished parts, trim, ceramics, etc.
- 4 widths: 19 - 22 - 25 - 38 mm.
- For use with a hammer and resharpenable with a file.
- Supplied in blister pack.
Weight: 525 g.


Zipcut Spot Weld Remover

Automotive > Bodywork Tools > Bodywork Tools
04001100
Brand::Sykes Pickavant

• Auto-centering tool for removal of spot welds

• Adjustable centering device enables depth of cut to be controlled

• 5/16” hex shank for use with drill chucks of 3/8” capacity

• Reversible screw-on cutter blade for longer life

Spare Parts:

• 04001400 - Spare Cutters

• 04001500 - Spare Pins (x3)




Spot Weld Drill - High Speed Cobalt Steel - 8mm Dia

Automotive > Bodywork Tools > Bodywork Tools
04020100
Brand::Sykes Pickavant

Stubby Type Drill

80mm - Length

8mm - Diameter

• High speed cobalt steel drills, for removal of spot welds without distortion




CryoCobalt™ Drill - 6.5mm dia

Automotive > Bodywork Tools > Bodywork Tools
04026500
Brand::Sykes Pickavant

• CryoCobalt™ Drills are specially designed for drilling very hard metals
• Ideal for drilling high strength alloy steels, ultra high strength boron steels,
as well as aluminium chassis, panels and rivets
• Added Cobalt increases micro-sharpness and operating temperatures
• Cryophase process improves flexibility and extends bit operating life
• CryoCobalt™ drills can be re-sharpened

Length: 105mm
Diameter: 6.5mm


Material: CM-88™ Chrome Moly Cobalt High Heat Steel
Heat Resistance: Up to 1200°F / 650°C
Hardness: 66-68Re
Tip Design: 135° Split Point
Coating: Gold Oxide
Cryophase: Patented thermal cycling cryogenic treatment




CryoCobalt™ Drill - 8mm Dia

Automotive > Bodywork Tools > Bodywork Tools
04028000
Brand::Sykes Pickavant

• CryoCobalt™ Drills are specially designed for drilling very hard metals
• Ideal for drilling high strength alloy steels, ultra high strength boron steels,
as well as aluminium chassis, panels and rivets
• Added Cobalt increases micro-sharpness and operating temperatures
• Cryophase process improves flexibility and extends bit operating life
• CryoCobalt™ drills can be re-sharpened

Length: 115mm
Diameter: 8mm


Material: CM-88™ Chrome Moly Cobalt High Heat Steel
Heat Resistance: Up to 1200°F / 650°C
Hardness: 66-68Re
Tip Design: 135° Split Point
Coating: Gold Oxide
Cryophase: Patented thermal cycling cryogenic treatment




Sheet Metal Cutter - 1.6mm capacity (16SWG) - Bench Mounted

Automotive > Bodywork Tools > Bodywork Tools
04200000
Brand::Sykes Pickavant

Sheet Metal Cutter - 1.6mm capacity (16SWG) - Bench Mounted

• Light weight roller type cutter suitable for straight, curved and angled cutting on mild steel metal up to 1.6mm thick

• Reversible ratchet action cuts sheet metal quickly and efficiently & makes angle cutting easier

• Cutter wheels incorporate replaceable shear pins to prevent damage from overloading

• PVC Handle for operator comfort

• Replacement cutter wheels available

• Can also be vice mounted (with 04200100 - vice mounting block)

Capacity: 1.6mm (16swg)

Body: 135 x 130 x 60mm

Handle: 300 x 27 x 6mm

Wheels:  50mm dia

Weight: 1.75kg

Spare Parts:

• 04200200 - Replacement Cutter Wheels (pair)
• 04200400 - Shear Pins (2 Pack)
• 04200300 - Ratchet Wheel
• 04200500 - Repair Kit

Optional Extra:

• 04200100 - Vice Mounting Block




door skinner crimping tool

Automotive > Bodywork Tools > Bodywork Tools
04310000
Brand::Sykes Pickavant

• Portable hand held crimping tool suitable for bending and crimping flanges when replacing door skins and body panels

• Tough, replaceable nylon pads prevent damage to door skin when crimping flanges

• Supplied 50mm wide nylon pad for faster crimping on straight edges

• High quality chrome plated tool with pvc coated handles for comfort

Length 310mm

Handles 200mm

Jaws - Width 16mm

Nylon Block 50 x 22mm

Weight  large 0.81kg

Spare Parts:

• 04310270 - 50mm Nylon Pad

 




trim tool set

Automotive > Bodywork Tools > Bodywork Tools
04550000
Brand::Sykes Pickavant

Trim Tool Set

• Set of five strong, flexible plastic angled, lever and panel pullers

• Ideal for roof linings, door trims, panel trims and moulding strips

• Designed to enable the safe removal of vehicle trim panels without damage




heavy duty pry spoon

Automotive > Bodywork Tools > Bodywork Tools
05120100
Brand::Sykes Pickavant

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

• For prying, levering and panel beating in areas that are inaccessible to dollies

• Heavy duty pry spoon specially designed for separating outer panels from the inner frame structure

- Length: 405mm

- Width: 63mm

- Weight: 1.48kg




Panel Beater Double Ended Shrinking Hammer

Automotive > Bodywork Tools > Bodywork Tools
05280000
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Shrinking Hammers: Useful in the final stages of panel finishing when slightly stretched areas of metal can be encountered. In using this type of beater, small amounts of metal are forced into the spaces created by the cross milling. They can also be used on cold aluminium but working on sheet steel will be quicker if heat is applied to the area. Whenever possible, such beating should be carried out on the inside of the panel to minimise resurfacing needed prior to painting. Syke-Pickavant does not recommend using the same individual tools on aluminium and steel.

Panel Beater Double Ended Shrinking Hammer 05280000

• Medium-weight, flat face shrinking hammer, specifically designed for panel beating on slightly stretched areas of metal

• Specially designed cross milled heads improves stretched areas by forcing small amounts of metal into spaces created by cross milling

- Round Face: 41mm
- Square Face: 38mm
- Head Width: 97mm
- Weight: 0.425kg

 




Panel Beater Straight Pein & Finish - Flat Face

Automotive > Bodywork Tools > Bodywork Tools
052900V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

 

• Medium-weight, flat face finishing panel beater with straight pein

- Round Face: 41mm

- Square Face: N/A

- Head Width: 130mm

- Weight: 0.425kg

 




Copper / Rawhide Hammer

Automotive > Bodywork Tools > Bodywork Tools
05320000
Brand::Sykes Pickavant

• A useful addition to any bodyshop tool kit, handy when refitting rubber boot and door opening seals
- Round Faces: 28.5mm
- Hammer Size: 2
- Length: 306mm
- Weight: 1.06kg




grid toe dolly

Automotive > Bodywork Tools > Bodywork Tools
05500100
Brand::Sykes Pickavant

• Convex curved grid-pattern face which assists in shrinking stretched areas of metal

- Length: 120mm

- Width: 58mm

- Depth: 28mm

- Weight: 1.16kg




round head dolly

Automotive > Bodywork Tools > Bodywork Tools
05570100
Brand::Sykes Pickavant

• Double-ended dolly for re-shaping rounded and contoured panels

• 1 x domed and 1 x flat round surface

- Length: 56mm

- Width: 56mm

- Depth: 56mm

- Weight: 0.73kg




heavy toe dolly

Automotive > Bodywork Tools > Bodywork Tools
055801V2
Brand::Sykes Pickavant

• Heavyweight toe dolly enables access in difficult to reach areas

• 1 x flat face and 1 x curved face

- Length: 125mm

- Width: 60mm

- Depth: 30mm

- Weight: 1.37kg




Panel Beater Standard Bumping - Flat Face

Automotive > Bodywork Tools > Bodywork Tools
056000V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

 • Medium-weight, flat face panel beater suitable for straightening thicker gauge metals where significant corrective force is required

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg




Panel Beater Standard Bumping - Crowned Face

Automotive > Bodywork Tools > Bodywork Tools
056100V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Medium-weight, crowned face panel beater suitable for straightening thicker gauge metals where significant corrective force is required

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg




Panel Beater Light Bumping - Crowned Face

Automotive > Bodywork Tools > Bodywork Tools
05620000
Brand::Sykes Pickavant

High quality alloy steel heads with hardened striking surfaces
• Fine quality octagonal wooden shafts fitted as standard
• Wood and steel wedged handles ensure maximum head retention with improved safety
• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers
Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Light-weight, crowned face panel beater suitable for applying measured force in area of light damage or on thinner gauge metal
- Round Face: 32mm
- Square Face: 25mm
- Head Width: 89mm
- Weight: 0.37kg

 

 

 




Panel Beater Straight Pein & Finish - Crowned Face

Automotive > Bodywork Tools > Bodywork Tools
056500V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Medium-weight, crowned face finishing panel beater with straight pein

- Round Face: 41mm

- Square Face: N/A

- Head Width: 130mm

- Weight: 0.425kg




Panel Beater Pick & Finishing - Crowned Face

Automotive > Bodywork Tools > Bodywork Tools
056600V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

 

• Medium-weight crowned face panel beater with round point pick head designed to remove low spots when finishing

- Round Face: 38mm

- Square Face: N/A

- Head Width: 135mm

- Weight: 0.43kg




panel beater light bumping flat face

Automotive > Bodywork Tools > Bodywork Tools
05680000
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers

Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

Light-weight, flat face panel beater suitable for applying measured force in areas of light damage or on thinner

gauge metal

- Round Face: 32mm

- Square Face: 25mm

- Head Width: 89mm

- Weight: 0.37kg




Panel Beater Shrinking & Flat Face Hammer

Automotive > Bodywork Tools > Bodywork Tools
056900V2
Brand::Sykes Pickavant

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

 

• Medium-weight flat face shrinking hammer, specifically designed for panel beating on slightly stretched areas of metal

• Twin head with 1 x round flat face and 1 x square, cross milled face

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg




Pry & Surfacing Spoon

Automotive > Bodywork Tools > Bodywork Tools
05730000
Brand::Sykes Pickavant

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

• Specially designed for panel beating work in restricted areas and for separating outer panels from inner frame structure
- Length: 295mm
- Width: 50mm
- Weight: 0.85kg

 

 




body repair kit - thatcham

Automotive > Bodywork Tools > Bodywork Tools
058500TH
Brand::Sykes Pickavant

“Thatcham™ Accredited” Body Repair Tool Kit 058500TH

“The first Body Repair Tool Kit to achieve Thatcham™ accreditation”

• General purpose 13 piece set of Body Repair Tools approved by Thatcham™ for Insurance Approved Body Repair work

• Supplied in steel tool box (52800000)

• Contents:

- 052900V2 - Panel Beater Straight Pein and Finish Flat Face

- 053000V2 - Panel Beater Pick and Finishing Flat Face

- 053700V2 - Panel Beater Pein and Finish Crowned Face

- 056900V2 - Panel Beater Flat Face and Shrinking Face

- 054301V2 - Thin Curved Dolly

- 054801V2 - Thin Toe Dolly

- 055201V2 - Utility Dolly

- 05730000 - Pry & Surfacing Spoon

- 05940000 - Bumping Tool - Flat

- 05710100 - Adjustable Body Blade Holder

- 05711100 - 9tpi Standard Cut Body Blade

- 05711200 - 12tpi Fine Cut Body Blade

- 05711500 - 6tpi Plasticut Body Blade




welding C clamp - 495mm

Automotive > Bodywork Tools > Bodywork Tools
06501400
Brand::Sykes Pickavant

• Large capacity deep throat clamp, with small gripping area, for awkward shapes and access

• Suitable for holding together sheet metal, body panels and other materials

• Powerful grip and deep throat ideal for handling awkward shapes encountered when welding, glueing, marking off and template making

• Small gripping area allows close up working and deep throat enables access around bulky and awkward shapes e.g. Door sills

Length: 495mm

Jaw Opening: 300mm

Jaw Width: 250mm

Throat Depth Closed: 165 - 405mm

Weight: 1.90kg

 




1302-DOUBLE END DOLLY ROUND PEIN HEAD

Automotive > Bodywork Tools > Bodywork Tools
1302
BETA

Double end dolly round convex pein head


1304-SOLE DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1304
BETA

Sole dolly


1305-TOE DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1305
BETA

Toe dolly


1305 Z-MILLED TOE DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1305/Z
BETA

Milled toe dolly


1306-HEEL DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1306
BETA

Heel dolly


1307-REGULAR DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1307
BETA

Regular dolly


1308-EGG DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1308
BETA

Egg dolly


1310-GENERAL PURPOSE DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1310
BETA

General purpose dolly


1312-ANVIL DOLLY

Automotive > Bodywork Tools > Bodywork Tools
1312
BETA

Anvil dolly


1326-CURVED ANGLE SPOON

Automotive > Bodywork Tools > Bodywork Tools
1326
BETA

Curved angle spoon


1327-HEAVY-DUTY SPOON

Automotive > Bodywork Tools > Bodywork Tools
1327
BETA

Heavy-duty spoon


1328-PRY AND BUMPING SPOON

Automotive > Bodywork Tools > Bodywork Tools
1328
BETA

Pry and bumping spoon


1329-DOUBLE-ENDED SPOON

Automotive > Bodywork Tools > Bodywork Tools
1329
BETA

Double-ended spoon


1330-LONG DOUBLE-ENDED SPOON

Automotive > Bodywork Tools > Bodywork Tools
1330
BETA

Long double-ended spoon


1331-BENDING IRON WITH LEATHER FACE

Automotive > Bodywork Tools > Bodywork Tools
1331
BETA

Bending iron with leather face


1335 BM-BUMPING BLADE PLASTIC HANDLE

Automotive > Bodywork Tools > Bodywork Tools
1335BM
BETA

Bumping blade with plastic handle


1338-BODY BLADE HOLDER FOR ITEM 1338R

Automotive > Bodywork Tools > Bodywork Tools
1338
BETA

Body blade holder for item 1338R


1369 /C11-ASSORTMENT OF 11 TOOLS IN CASE

Automotive > Bodywork Tools > Bodywork Tools
1369/C11
BETA

Assortment of 11 tools


1477 K/7-BENT REV. RATCHETING WR. + BITS

Automotive > Bodywork Tools > Bodywork Tools
1477K/7
BETA

Kit with bent reversible ratcheting wrench and bits


1478-PIN REMOVING PLIERS

Automotive > Bodywork Tools > Bodywork Tools
1478
BETA

Pin removing pliers


1479-TRIM PIN REMOVER

Automotive > Bodywork Tools > Bodywork Tools
1479
BETA

Trim pin remover


** SPECIAL OFFER PRICE **

1479 N/S5-KIT 5 NYLON TRIM PIN REMOVERS

Automotive > Bodywork Tools > Bodywork Tools
1479N/S5
BETA

Kit of 5 nylon trim pin removers


** SPECIAL OFFER PRICE **

1479 RB/1-STRAIGHT PUTTY KNIFE SCRAPER

Automotive > Bodywork Tools > Bodywork Tools
1479RB/1
BETA

Straight putty knife scraper


1479 U/13-SET OF 3 PUTTY KNIFE SCRAPERS

Automotive > Bodywork Tools > Bodywork Tools
1479U/13
BETA

Set of 3 putty knife scrapers


1479 U/32-TRIM PIN REMOVER STEEL BLADE

Automotive > Bodywork Tools > Bodywork Tools
1479U/32
BETA

Trim pin remover stainless steel blade


1479 RB/2-BENT PUTTY KNIFE SCRAPER

Automotive > Bodywork Tools > Bodywork Tools
1479_RB_2
BETA

Bent putty knife scraper


End mills

Automotive > Bodywork Tools > Bodywork Tools
Facom

- Super fast HSS steel self-centring and resharpenable drill bits.
- Available in sets of 2 identical diameter bits (J2) or 3 different diameter bits (J3).


Welding spot mill

Automotive > Bodywork Tools > Bodywork Tools
230
Facom

- This tool, fitted on a drill, separates two spot-welded metal sheets.
- Includes the mill holder assembly, reversible mill and centring tip.
- Not compatible with ref V.781B.
- Length: 70 mm.
Weight: 23 g.
- Set of 5 spare tips: 230.A1J5.


Set of mills

Automotive > Bodywork Tools > Bodywork Tools
230.J1
Facom

- Set with a 230 module, 2 centring tips and 10 reversible mills.
- Dimensions (L. x W. x H.): 115 x 65 x 22 mm.
Weight: 90 g.
- Set of 5 spare tips: ref 230.A1J5.


4PC BODY FILLER APLIC. SET

Automotive > Bodywork Tools > Bodywork Tools
46449
Brand::Draper

BFASB


850 milled files

Automotive > Bodywork Tools > Bodywork Tools
Facom

- Recommended for soft metal, cast iron, mild steel and soft plastics.
- For use with frame 851B.


861D - Bumping hammers

Automotive > Bodywork Tools > Bodywork Tools
861D.26
Facom

- Stretching and planishing hammer.
- Convex, round and square heads.
- Secure handle attachment.
- Finely polished planishing surfaces.
- Facetted hickory handle.
- Spare handle and wedge: 211.MH26.


861D - Bumping hammers

Automotive > Bodywork Tools > Bodywork Tools
861D.30
Facom

- Stretching and planishing hammer.
- Convex, round and square heads.
- Secure handle attachment.
- Finely polished planishing surfaces.
- Facetted hickory handle.
- Spare handle and wedge: 211.MH26.


Round, flat, and convex head hammer

Automotive > Bodywork Tools > Bodywork Tools
861D.RPC
Facom

- Bumping and planishing hammer.
- Flat, round and convex heads.
- Secure handle attachment.
- Finely polished heads.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


Wide-dome dresser

Automotive > Bodywork Tools > Bodywork Tools
864D.60
Facom

- Surface curved widthwise.
- Secure handle attachment.
- Finely polished head.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


866D - Shrinking hammers

Automotive > Bodywork Tools > Bodywork Tools
866D.32
Facom

- Stretching and planishing hammer.
- 1 round ribbed face, one square smooth face.
- Secure handle attachment.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


Shrinking dresser no.1

Automotive > Bodywork Tools > Bodywork Tools
867D
Facom

- Ribbed face.
- Secure handle attachment.
- Finely polished head.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


Hammer with round domed face and curved pein

Automotive > Bodywork Tools > Bodywork Tools
868D.40BOC
Facom

- Planishing hammer.
- 1 round domed face, 1 curved pein.
- Secure handle attachment.
- Finely polished head.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


Hammer with round flat face and straight pein

Automotive > Bodywork Tools > Bodywork Tools
868D.40PLD1
Facom

- Planishing hammer.
- 1 round flat face, 1 straight pein.
- Secure handle attachment.
- Finely polished head.
- Hickory handle.
- Spare handle and wedge: 211.MH26.


Regular dolly no.2

Automotive > Bodywork Tools > Bodywork Tools
870B
Facom

- Combination of sharp and rounded edges.
- Dimensions (L. x W. x H.): 90 x 55 x 35 mm.
- Finish: polished.
Weight: 1.150 kg.


Slim wedge dolly

Automotive > Bodywork Tools > Bodywork Tools
871B.45
Facom

- Slim model with a domed face.
- Dimensions (L. x W. x H.): 125 x 55 x 37 mm.
- Finish: polished.
Weight: 900 g.


Dished dolly

Automotive > Bodywork Tools > Bodywork Tools
874A
Facom

- Curved on all sides.
- Dimensions (L. x W. x H.): 106 x 65 x 26 mm.
- Finish: polished.
Weight: 980 g.


Long single spoon

Automotive > Bodywork Tools > Bodywork Tools
875.3
Facom

- Bumping spoon.
- Length: 390 mm.
- Finish: polished.
Weight: 1.300 kg.


Flat shrinking blade

Automotive > Bodywork Tools > Bodywork Tools
891A.PL
Facom

- Ribbed face.
- Length: 350 mm.
Weight: 700 g.


Short single spoon

Automotive > Bodywork Tools > Bodywork Tools
895A
Facom

- Bumping spoon.
- Length: 285 mm.
- Finish: varnished and polished.
Weight: 820 g.


Pinch wedge dolly

Automotive > Bodywork Tools > Bodywork Tools
906A
Facom

- One curved face and one flat face.
- Dimensions (L. x W. x H.): 130 x 68 x 25 mm.
- Finish: polished.
Weight: 1.150 kg.


Hand crimper and punch

Automotive > Bodywork Tools > Bodywork Tools
CAD.10
Facom

- Crimp width: 12 mm.
- Punch 5 mm.
- Swivel head.
- Max. sheet thickness: 0.8 mm.
- Dimensions (L. x W. x H.): 290 x 130 x 30 mm.
Weight: 1.200 kg.
- Punch and die, 5 mm diameter: CAD.10RN1.


Trim clip removal plier

Automotive > Bodywork Tools > Bodywork Tools
CR.D1
Facom

- For quickly removing staples, clips, door panels, facia and trim supports, etc.
- Wide nose for undoing facings without risk of breaking or tearing panels.
- Finger guard to avoid injury.
- Designed for accessing difficult-to-reach places.
- Length: 240 mm.
- Finish: black head, chrome pliers.
Weight: 190 g.


Windshield wiper arm remover

Automotive > Bodywork Tools > Bodywork Tools
CR.D10
Facom

- Including spacer for wiper arms with integral washer jet.
- Each leg can be removed for a better fit on the arm.
- Capacity diam.: 44 mm.
- Supplied with instructions.
Weight: 220 g.


Magnetic Painting Clamp

Automotive > Bodywork Tools > Bodywork Tools
CR.SMP
Facom




Trim removal tool

Automotive > Bodywork Tools > Bodywork Tools
D.115A
Facom

- For removing interior door trimmings without damage.
- Dimensions (L. x W. x H.): 155 x 32 x 45 mm.
Weight: 106 g.


Fastener removal tool

Automotive > Bodywork Tools > Bodywork Tools
D.137A
Facom

- For removing plastic fasteners securing carpets, trim and panels.
- Capacity:
- Fitter diameter: 9 to 22 mm springs.
- Body diameter: 4 to 9 mm springs.
- Dimensions (L. x W. x H.): 200 x 28 x 40 mm.
Weight: 110 g.


Windshield replacement kit

Automotive > Bodywork Tools > Bodywork Tools
D.28B
Facom

- Comprising:
- D.28A1: Suction cups (2x).
- D.28A2: Ratchet strap.
- D.28-3: Removal tool.
- D.28-4: Pull handle.
- D.28-5: Braided wire for windshields (18 m).
Weight: 3.300 kg.


Windshield tools

Automotive > Bodywork Tools > Bodywork Tools
D.80
Facom

- Set of 3 tools.
- Comprising:
- D.80-01: Windshield fitting tool.
- D.80-02: Trim fitting tool.
- 82H.4: Hexagon key (4 mm).
- Supplied in a plastic case, dim. (L. x W. x H.): 325 x 135 x 50 mm.
Weight: 820 g.
- For narrow trim: D.80-02-04.
- For medium trim: D.80-02-05.
- For wide trim: D.80-02-06.


Set of 6 suction cups

Automotive > Bodywork Tools > Bodywork Tools
DCR.20J6
Facom

- Secures components while curing.
- Many bodywork applications:
- Windshield trims.
- Names and badges.
- Interior mirrors, etc.
- Excellent suction on painted panels and windows.
Weight: 470 g.


1338 BLADE HOLDER WITH FLAT BLADES

Automotive > Bodywork Tools > Bodywork Tools
BETA

Adjustable body blade holder with flexible flat blades


1338 R SPARE BODY BLADES FOR 1338A-B

Automotive > Bodywork Tools > Bodywork Tools
BETA

Spare body blades for item 1338A-B


Suction Cups

Automotive > Bodywork Tools > Bodywork Tools
Brand::Bitz




Number of Products Found: 107